Get exclusive volume discounts, bulk pricing updates, and new product alerts delivered directly to your inbox.
By subscribing, you agree to our Terms of Service and Privacy Policy.
Direct access to our certified experts
Range: 0 to 60V at 0 to 1.5A
Output Setting & Control
Voltage Setting: By coarse and fine controls.
Current Setting: By single logarithmic control.
Low Current Range: Reduces max. current to 75mA and increases resolution to 0.01mA.
Output Mode: Constant voltage or constant current with automatic cross-over.
CC indicator lit in constant current mode.
Output Switch: Electronic, non isolating. Preset voltage and current limit displayed
when Output is off. Output rise time no load <20ms.
View Settings: With the output On, the meters show actual voltage and current.
The preset levels can be viewed and adjusted at any time by pressing
the View Settings button
V-Span
(Voltage Span Control)
The voltage adjustment range can be controlled by digital setting of the end-stop values of
the coarse voltage control to any desired values. The range for Vmax is 1V to 120V or 250V
depending on model. The range for Vmin is 0 to (Vmax – 1V).
S-Lock
(Settings Lock)
Voltage and current settings can be locked by a single button press. Lock accuracy is equal to
the meter accuracy (see Meter Specification).
Output Performance
Ripple & Noise: Normal mode voltage: <2mV rms and 10mV p-p
Normal mode current: <10uA rms ; <1uA rms on 75mA range
Common mode current: <20uA rms
Load Regulation: Voltage - <0·01% + 10mV.
Current - typically 0·01% + 50µA.
Line Regulation: Voltage <0·01% + 10mV for 10% line change.
Current <0·01% + 50µA. for 10% line change.
Transient Response: <250µs to within 50mV of setting for a 90% load change.
Temp. Coefficient: Voltage: typically <(50ppm + 2mV)/°C
Current: typically <(100ppm + 0.1mA)/°C;
<(100ppm + 0.01mA)/°C on 75mA range
Output Protection
Output Protection: Output will withstand forward voltages of up to rated output voltage.
Reverse protection by diode clamp for currents to 3A.
OVP and OCP Trips: Voltage or current measured to be in excess of 105% of the rated
maximum will cause the output to trip off.
Over-temperature: Output trips off for over-temperature.
Safety Interlocks: Operations that could cause an unexpected change in voltage or
current settings are interlocked with the output switch.
Output Connections
Output Terminals: Universal 4mm safety binding posts on 19mm (0·75”) spacing.
Terminals can accept fixed shroud 4mm plugs, standard 4mm plugs, fork terminals and bare wires.
Remote Sense
Sense Selection: Voltage sensing is selected as Local or Remote by front panel switch.
Sense Terminals: Sprung loaded screw-less terminals.
METER SPECIFICATIONS
Display Type: Dual 4-digit meters, 10mm (0·39”) LED.
Voltage Meter
Resolution: 100mV
Accuracy: ± (0·1% of reading + 100mV)
Current Meter
Resolution: 0.1mA (0·01mA on 75mA range)
Accuracy: ± (0·3% + 0.3mA); ± (0·3% + 0·03mA) on 75mA range
Meter Damping: Normally 20ms, switchable to 2 sec for averaging rapidly varying loads
DIGITAL BUS INTERFACES (PLH-P models only)
The standard PL-P product offers full remote control and read-back using RS-232, USB or LAN
(LXI-C). All interfaces are at ground potential and opto-isolated from the output terminals.
Note: Remote/Local Sense, and Operational Mode (PL303QMD-P) are manually selectable only.
RS-232
Standard 9-pin D connector. Baud rate 9,600.
USB
Standard USB 2.0 connection (backwards compatible with USB 1.x). Operates as a virtual
COM port.
Ethernet (LAN)
Standard 10/100 base-T hardware connection. ICMP and TCP/IP Protocol for connection to
Local Area Network or direct connection to a single PC.
LXI Compliance
LAN interface is compliant with LXI-C. (LXI is the abbreviation for Lan eXtensions for
Instrumentation). For more information visit: www.tti-test.com/go/lxi
GPIB INTERFACE (Option G, factory fit only)
Option G adds a GPIB (IEEE-488) interface.
This is in addition to the RS-232, USB and LAN interfaces of the standard PL-P product. The
interface conforms with IEEE-488.1 and IEEE-488.2
DIGITAL PROGRAMMING PERFORMANCE (PLH-P models only)
Voltage Setting
Setting Resolution: 10mV
Setting Accuracy: ± (0.05% +50mV)
Current Setting
Setting Resolution: 0.1mA (0.01mA on 75mA range)
Setting Accuracy: ± (0.3% +0.1mA); ± (0.3% +0.01mA) on 75mA range
Programming Speed
Command Delay: Typically <25ms (this must be added to any of the figures below)
Voltage Up Time: Typically <45ms* to 1%
Voltage Down Time: Typically <200ms* to 1% (full load); typically <500ms* to 1% (no load)
* The up and down times vary with model, current range and voltage step size. More
information is contained in the operating manual - downloadable from our web site.
Voltage Readback
Resolution: 10mV
Accuracy: ± (0.1% +50mV)
Current Readback
Resolution: 0.1mA (0.01mA on 75mA range)
Accuracy: ± (0.3% +0.1mA); ± (0.3% +0.01mA) on 75mA range
VARIABLE OVP and OCP PROTECTION (PLH-P models only)
Measure-and-compare over-voltage and over-current protection are implemented in firmware
and can be set via the remote interfaces only. Output trips Off for OVP and OCP conditions.
Setting resolution: 100mV and 0.1mA.
Response time: typically 500ms
ANALOG REMOTE CONTROL (PLH-P models only)
Isolated analog voltage control of voltage and current. Non-isolated analog control outputs
are also provided to enable easy parallel connection of multiple units in a master-slave
configuration.
Control Inputs (Isolated)
Reference Point: Control input voltages are referenced to their own return points.
Set Voltage Input: 0V to 10V sets 0 to 100% of rated output (e.g. 0 to 120V for PLH120-P).
Alternative scaling of 0V to 5V (selectable using internal link).
Set Current Input: 0V to 10V sets 0 to 100% of rated output (0 to 750mA for PLH120-P).
Alternative scaling of 0V to 5V (selectable using internal link).
Set Voltage Accuracy: ± (0.3% +100mV); Input Impedance = 10kW
Set Current Accuracy: ± (0.5% +0.5mA); Input Impedance = 10kW
Control Outputs (Non-isolated)
Reference Point: Control output voltages are referenced to the positive output terminal.
Voltage Output: 0 to 100% of rated output voltage generates 0V to 5V.
Current Output: 0 to 100% of rated output current generates 0V to 5V.
Voltage Out Accuracy:± (0.3% +100mV); Output Impedance = 125W
Current Out Accuracy: ± (0.5% +0.5mA); Output Impedance = 125W
Note that Analog control of current can not be used with the low current range selected.
REMOTE ANALOG ON/OFF CONTROL (PLH-P models only)
Non-isolated terminal which sets the output to Off when pulled low by gate signal or relay
closure. Signal is reference to the positive output terminal.
DRIVER SOFTWARE SUPPLIED (PLH-P models only)
IVI Driver
An IVI driver for Windows is supplied. This provides support for common applications such as
LabView*, LabWindows*, HPVEE* etc.
USB Driver
An installation file is supplied which calls a standard Windows* USB driver.
GENERAL SPECIFICATIONS
Input
AC Input: 230V AC or 115V AC ± 10%, 50/60Hz. Installation Category II
Input Power: 280VA max.
Temperature & Environmental
Operating Range: +5ºC to +40ºC, 20% to 80% RH
Storage Range: -40ºC to + 70ºC
Environmental: Indoor use at altitudes up to 2000m, Pollution Degree 2.
Cooling: Intelligent variable-speed low noise fan assists convection.
Safety & EMC
Safety: Complies with EN61010-1
EMC: Complies with EN61326
Physical
Size: PLH models - 107mm x 131mm (¼ rack 3U) x 288mm,
PLH-P models - 107mm x 131mm (¼ rack 3U) x 315mm,
(sizes exclude feet, knobs and terminals).
Weight: PLH models - 4·9kg;
PLH-P models - 5.0kg
GENERAL SPECIFICATIONS
Input
AC Input: 230V AC or 115V AC ± 10%, 50/60Hz. Installation Category II
Input Power: 280VA max.
Temperature & Environmental
Operating Range: +5ºC to +40ºC, 20% to 80% RH
Storage Range: -40ºC to + 70ºC
Environmental: Indoor use at altitudes up to 2000m, Pollution Degree 2.
Cooling: Intelligent variable-speed low noise fan assists convection.
Safety & EMC
Safety: Complies with EN61010-1
EMC: Complies with EN61326
Physical
Size: PLH models - 107mm x 131mm (¼ rack 3U) x 288mm,
PLH-P models - 107mm x 131mm (¼ rack 3U) x 315mm,
(sizes exclude feet, knobs and terminals).
Weight: PLH models - 4·9kg;
PLH-P models - 5.0kg
