Aim TTI TG1006 Function Generator (10Mhz)

WAVEFORMS

Sine

Range: 1mHz to 10MHz

Resolution: 1mHz or 6 digits

Accuracy: 10 ppm for 1 year; ± 1mHz below 0.2Hz

Temperature Stability: Typically <1 ppm="" c="" outside="" 18="" to="" 28="" c="" br=""> Output Level: 1mV to 10Vp-p into 50W

Harmonic Distortion: <0.3% THD to 20kHz (typically 0.1%), <–45dBc to 300kHz,

<-30dbc to="" 10mhz="" typically="" -35dbc="" br=""> Non-harmonic Spurii: <–55dBc to 1MHz, <–55dBc + 6dB/octave 1MHz to 10MHz

Square

Range: 1mHz to 10MHz

Resolution: 1mHz or 6 digits

Symmetry Control: 20% to 80% 1mHz to 10MHz

Accuracy: 10 ppm for 1 year; ± 1mHz below 0.2Hz

Output Level: 1mV to 10Vp-p into 50W

Rise and Fall Times: <25ns

Aberrations: <5% + 2mV

Triangle

Range: 1mHz to 1 MHz

Resolution: 1mHz or 6 digits

Accuracy: 10 ppm for 1 year; ± 1mHz below 0.2Hz

Output Level: 1mV to 10Vp-p into 50W

Linearity Error: <0.5% to 100 kHz

OPERATING MODES

Continuous

Continuous cycles of the selected waveform are output at the programmed frequency.

Sweep

Carrier Waveforms: All

Sweep Mode: Manual, linear or logarithmic, single or continuous.

Sweep Width: From 0.1Hz to 10MHz in one range. Phase continuous. Independent setting

of the start and stop frequency.

Sweep Time: 100ms to 999s (10ms resolution).

Sweep SYNC: Start of sweep trigger available from SYNC output.

Trigger Source: The sweep may be free run or triggered from the front panel MAN TRIG key.

Manual Sweep Mode: An analogue control can be used to set any frequency between the sweep

start and sweep stop frequencies.

Amplitude Modulation

Carrier Frequency: From 1mHz to 10MHz.

Carrier Waveforms: All

Modulation Frequency: 400Hz internal. DC to 20kHz external

External Modulation: AM/COUNT IN socket

Frequency Shift Keying (FSK)

Phase coherent switching between two selected frequencies at a rate defined by the switching signal

source.

Carrier frequency: From 0.1Hz to 10MHz.

Carrier waveforms: All

Switch repetition rate: DC to 10kHz (internal trigger).

Switching signal source: Manual (front panel MAN TRIG key) or internal trigger generator

Frequency List

Carrier Waveforms: All

Frequency List: Up to 10 frequencies from 1mHz to 10MHz

Switching Source: Manual from front panel MAN TRIG key

OUTPUTS

Main Outputs

Output Impedance: 50W and 600W (not independent)

Amplitude: 2mV to 20V pk-pk open circuit, (1mV to 10V pk-pk into 50W/600W) in four

switch selectable ranges with 20dB vernier control within each range.

(Amplitude can be displayed in pk-pk or r.m.s.)

Attenuator: 0, -20dB, -40dB, or -60dB.

Amplitude Flatness: ±0.2dB to 500kHz; ±2dB to 10MHz.

DC Offset Range: ±10V. DC offset plus signal peak limited to ±10V from 50W/600W;

CLIP shows in display when offset plus signal peak exceeds ±10V. DC offset

plus waveform attenuated proportionally by the attenuator.

Resolution: 3 digits for both Amplitude and DC Offset

Datasheet